GMC Vehicle Models Canyon 2004-2012
GMC Vehicle Models Canyon 2004-2012 Torque Specifications
Complete GMC Vehicle Models Canyon 2004-2012 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
2.8l Engine
Torque specifications for 2.8L Engine
2.8l Engine
Torque specifications for 2.8L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
Crankshaft And Bearings
1 Main Bearing Bolts
M10 x 1.25
1
Main Bearing Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment of the main bearing caps before tightening.
2 Connecting Rod Nuts
M8 x 1.25
2
Connecting Rod Nuts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of the connecting rod caps.
Flywheel And Harmonic Balancer
1 Flywheel Bolts
M12 x 1.5
1
Flywheel Bolts
M12 x 1.5
Torque Specification
96 ft-lbs (130 N·m)
Important Notes
Use thread locker on bolt threads as specified by the manufacturer.
2 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
Torque Specification
132 ft-lbs (180 N·m)
Important Notes
Ensure the crankshaft is properly secured before tightening.
Oil System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Ensure the oil pan gasket is properly aligned before tightening.
2 Oil Drain Plug Bolt
M14 x 1.5
2
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Replace the crush washer with a new one during installation.
Valve Train
1 Rocker Arms/Shafts Bolts
M8 x 1.25
1
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Ensure proper alignment of the rocker arms before tightening.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly aligned before tightening.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the camshaft is properly aligned before tightening.
Intake And Exhaust
1 Intake Manifold Bolts
M8 x 1.25
1
Intake Manifold Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the intake manifold gasket is properly aligned before tightening.
2 Exhaust Manifold/Headers Bolts
M8 x 1.25
2
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the exhaust manifold gasket is properly aligned before tightening.
Cooling System
1 Water Pump Bolts
M8 x 1.25
1
Water Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the water pump gasket is properly aligned before tightening.
2 Thermostat Housing Bolts
M6 x 1.0
2
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the thermostat housing gasket is properly aligned before tightening.
Accessory Drive
1 Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.25
1
Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.25
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Ensure the belt tensioner is properly aligned before tightening.
2 Alternator Mounting Bolts
M10 x 1.25
2
Alternator Mounting Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the alternator is properly aligned before tightening.
Fuel System
1 Fuel Pump Mounting Bolts
M6 x 1.0
1
Fuel Pump Mounting Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the fuel pump gasket is properly aligned before tightening.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the fuel injector O-rings are properly seated before tightening.
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the spark plug threads are clean and free of debris.
Emissions Control
1 EGR Valve Bolts
M6 x 1.0
1
EGR Valve Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the EGR valve gasket is properly aligned before tightening.
3.5l Engine
Torque specifications for 3.5L Engine
3.5l Engine
Torque specifications for 3.5L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Follow a specific torque sequence as outlined in the service manual. Failure to do so may result in head gasket failure.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Ensure rocker arms are properly seated before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M10 x 1.25
1
Main Bearing Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Follow the specified torque sequence to ensure even clamping force.
2 Connecting Rod Nuts
M8 x 1.0
2
Connecting Rod Nuts
M8 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure connecting rods are properly seated on the crankshaft journals.
3 Flywheel Bolts
M12 x 1.5
3
Flywheel Bolts
M12 x 1.5
Torque Specification
96 ft-lbs (130 N·m)
Important Notes
Use thread locker on flywheel bolts to prevent loosening.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the camshaft sprocket is properly seated before tightening.
Intake And Exhaust
1 Intake Manifold Bolts
M8 x 1.25
1
Intake Manifold Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the specified torque sequence to ensure even clamping force.
2 Exhaust Manifold/Headers Bolts
M10 x 1.25
2
Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use new gaskets and ensure proper alignment before tightening.
Cooling System
1 Water Pump Bolts
M8 x 1.25
1
Water Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use thread sealant on bolts that penetrate the water jacket.
2 Thermostat Housing Bolts
M6 x 1.0
2
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the thermostat is properly seated before tightening.
Accessory Drives
1 Starter Motor Mounting Bolts
M10 x 1.25
1
Starter Motor Mounting Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the starter motor is properly aligned before tightening.
2 Alternator Mounting Bolts
M10 x 1.25
2
Alternator Mounting Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the alternator is properly aligned before tightening.
3.7l Engine
Torque specifications for 3.7L Engine
3.7l Engine
Torque specifications for 3.7L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Ensure rocker arms are properly aligned before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Follow the manufacturer's torque sequence for main bearing caps.
2 Connecting Rod Nuts
M8 x 1.25
2
Connecting Rod Nuts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure connecting rods are properly aligned before tightening.
3 Flywheel Bolts
M12 x 1.75
3
Flywheel Bolts
M12 x 1.75
Torque Specification
96 ft-lbs (130 N·m)
Important Notes
Use thread locker on flywheel bolts to prevent loosening.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.5
2
Camshaft Sprocket Bolt
M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the camshaft is properly aligned before tightening.
Cooling System
1 Water Pump Bolts
M8 x 1.25
1
Water Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the water pump gasket is properly seated before tightening.
2 Thermostat Housing Bolts
M6 x 1.0
2
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the thermostat is properly seated before tightening.
Oil System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2 Oil Drain Plug Bolt
M14 x 1.5
2
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Replace the crush washer with each oil change.
Intake And Exhaust
1 Intake Manifold Bolts
M8 x 1.25
1
Intake Manifold Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
2 Exhaust Manifold/Headers Bolts
M8 x 1.25
2
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the exhaust manifold gasket is properly seated before tightening.
Accessories
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the starter motor is properly aligned before tightening.
2 Alternator Mounting Bolts
M10 x 1.5
2
Alternator Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper belt tension before tightening.
3 Power Steering Pump Mounting Bolts
M10 x 1.5
3
Power Steering Pump Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper belt tension before tightening.
4l60 Transmission
Torque specifications for 4l60 Transmission
4l60 Transmission
Torque specifications for 4l60 Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M10 x 1.5
1
Transmission Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of the transmission during installation.
Oil Pan
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.83 ft-lbs (12 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
Fluid Management
1 Transmission Drain and Fill Plugs
M12 x 1.5
1
Transmission Drain and Fill Plugs
M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the threads are clean and free of debris before installation.
2 Transmission Cooler Line Fittings
M12 x 1.5
2
Transmission Cooler Line Fittings
M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the fittings are properly aligned to prevent leaks.
Drivetrain Connection
1 Drive Axle/Half Shaft Bolts
M12 x 1.5
1
Drive Axle/Half Shaft Bolts
M12 x 1.5
Torque Specification
118 ft-lbs (160 N·m)
Important Notes
Ensure the drive axles are properly seated before tightening.
2 Propeller/Drive Shaft Bolts
M10 x 1.5
2
Propeller/Drive Shaft Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the drive shaft is properly aligned with the transmission output yoke.
Starter Motor
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the starter motor is properly aligned with the flywheel.
Bell Housing
1 Bell Housing Bolts
M10 x 1.5
1
Bell Housing Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the bell housing is properly aligned with the engine block.
Torque Converter
1 Torque Converter Bolts
M10 x 1.5
1
Torque Converter Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the torque converter is properly seated on the flexplate.
Valve Body
1 Valve Body Bolts
M6 x 1.0
1
Valve Body Bolts
M6 x 1.0
Torque Specification
7.38 ft-lbs (10 N·m)
Important Notes
Ensure the valve body is properly seated before tightening.
Shift Linkage
1 Shift Linkage Bolts
M8 x 1.25
1
Shift Linkage Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the shift linkage is properly aligned before tightening.
5.3l Engine
Torque specifications for 5.3L Engine
5.3l Engine
Torque specifications for 5.3L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
Crankshaft And Bearings
1 Main Bearing Bolts
M10 x 1.5
1
Main Bearing Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment of the crankshaft before tightening.
2 Connecting Rod Nuts
M8 x 1.25
2
Connecting Rod Nuts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of the connecting rod before tightening.
Flywheel And Harmonic Balancer
1 Flywheel Bolts
M12 x 1.5
1
Flywheel Bolts
M12 x 1.5
Torque Specification
96 ft-lbs (130 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening.
2 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
Torque Specification
132 ft-lbs (180 N·m)
Important Notes
Use a harmonic balancer installation tool to prevent damage during tightening.
Oil System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2 Oil Pressure Sensor Bolt
M8 x 1.25
2
Oil Pressure Sensor Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar sensor bolts.
Valvetrain
1 Rocker Arms/Shafts Bolts
M8 x 1.25
1
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Ensure proper alignment of the rocker arms before tightening.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.
Body
Torque specifications for Body
Body
Torque specifications for Body
Body Mounts
1 Body Mount Bolts
M10 x 1.5
1
Body Mount Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure even tightening sequence to avoid misalignment.
Doors
1 Door Hinge Bolts
M8 x 1.25
1
Door Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure door alignment before final torque application.
2 Tailgate Hinge Bolts
M8 x 1.25
2
Tailgate Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure tailgate alignment before final torque application.
Safety Components
1 Seat Belt Anchor Bolts
M10 x 1.5
1
Seat Belt Anchor Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Critical for passenger safety. Do not under-torque.
2 Spare Tire Carrier Bolts
M10 x 1.5
2
Spare Tire Carrier Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure spare tire is securely attached.
Exterior Panels
1 Fender Bolts
M6 x 1.0
1
Fender Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment with adjacent panels.
2 Bumper Mounting Bolts
M8 x 1.25
2
Bumper Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bumper alignment before final torque application.
3 Hood Hinge Bolts
M8 x 1.25
3
Hood Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure hood alignment before final torque application.
Roof Components
1 Roof Rack Bolts
M6 x 1.0
1
Roof Rack Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure even tightening to prevent loosening under load.
Front End Components
1 Radiator Support Bolts
M8 x 1.25
1
Radiator Support Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the radiator and front-end components.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Brake Caliper System
1 Brake Caliper Bolts
M12 x 1.5
1
Brake Caliper Bolts
M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
These bolts secure the brake caliper to the mounting bracket. Ensure proper alignment before torquing.
2 Brake Caliper Mounting Bracket Bolts
M14 x 1.5
2
Brake Caliper Mounting Bracket Bolts
M14 x 1.5
Torque Specification
129 ft-lbs (175 N·m)
Important Notes
These bolts attach the caliper mounting bracket to the steering knuckle or axle. Ensure the bracket is seated properly before torquing.
3 Brake Hose Banjo Bolt
M10 x 1.0
3
Brake Hose Banjo Bolt
M10 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
This bolt connects the brake hose to the caliper. Ensure the sealing washers are in good condition and properly seated.
Brake Rotor Drum System
1 Brake Disc/Drum Retaining Bolts
M10 x 1.25
1
Brake Disc/Drum Retaining Bolts
M10 x 1.25
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
These bolts secure the brake rotor or drum to the hub. Ensure the rotor/drum is seated properly before torquing.
Wheel And Hub System
1 Wheel Lug Nuts
M12 x 1.5
1
Wheel Lug Nuts
M12 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
These nuts secure the wheel to the hub. Always torque in a star pattern to ensure even clamping force.
Brake Hydraulic System
1 Brake Master Cylinder Mounting Bolts
M8 x 1.25
1
Brake Master Cylinder Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts secure the master cylinder to the brake booster. Ensure the master cylinder is properly aligned before torquing.
2 Brake Booster Mounting Bolts
M8 x 1.25
2
Brake Booster Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts secure the brake booster to the firewall. Ensure the booster is properly seated before torquing.
Brake Pedal System
1 Brake Pedal Assembly Bolts
M8 x 1.25
1
Brake Pedal Assembly Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts secure the brake pedal assembly to the firewall or pedal bracket. Ensure the pedal operates smoothly before torquing.
Abs System
1 ABS Sensor Mounting Bolts
M6 x 1.0
1
ABS Sensor Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
These bolts secure the ABS wheel speed sensor to the steering knuckle or axle. Ensure the sensor is properly aligned before torquing.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine Transmission Interface
1 Flywheel Bolts
M10 x 1.25
1
Flywheel Bolts
M10 x 1.25
Torque Specification
96 ft-lbs (130 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening. Use a crisscross pattern for torque sequence.
2 Transmission Bellhousing Bolts
M8 x 1.25
2
Transmission Bellhousing Bolts
M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the transmission is properly aligned with the engine before tightening.
Transmission Components
1 Transmission Mounting Bolts
M10 x 1.5
1
Transmission Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the transmission is properly supported before tightening.
2 Transmission Oil Pan Bolts
M6 x 1.0
2
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing of the oil pan gasket.
3 Transmission Drain and Fill Plugs
M12 x 1.75
3
Transmission Drain and Fill Plugs
M12 x 1.75
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the transmission fluid is at the correct level after tightening.
Driveshaft And Axles
1 Drive Axle/Half Shaft Bolts
M12 x 1.5
1
Drive Axle/Half Shaft Bolts
M12 x 1.5
Torque Specification
118 ft-lbs (160 N·m)
Important Notes
Ensure the axle is properly seated in the differential before tightening.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
177 ft-lbs (240 N·m)
Important Notes
Ensure the CV joint is properly seated in the wheel hub before tightening.
3 Propeller/Drive Shaft Bolts
M8 x 1.25
3
Propeller/Drive Shaft Bolts
M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the driveshaft is properly aligned before tightening.
Differential And Transfer Case
1 Differential Drain/Fill Plug
M14 x 1.5
1
Differential Drain/Fill Plug
M14 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the differential fluid is at the correct level after tightening.
2 Transfer Case Drain/Fill Plug
M14 x 1.5
2
Transfer Case Drain/Fill Plug
M14 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the transfer case fluid is at the correct level after tightening.
3 Transfer Case Mounting Bolts
M10 x 1.5
3
Transfer Case Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the transfer case is properly aligned before tightening.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Ignition System
1 Ignition Coil Bolt
M6 x 1.0
1
Ignition Coil Bolt
M6 x 1.0
Torque Specification
5.92 ft-lbs (8 N-m)
Important Notes
Torque value is critical for ensuring proper electrical performance. Value is estimated based on typical ignition coil bolt size.
Starting System
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N-m)
Important Notes
Ensure starter motor is properly aligned before torquing. Value is estimated based on typical starter motor bolt size.
Charging System
1 Alternator Mounting Bolts
M10 x 1.5
1
Alternator Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N-m)
Important Notes
Ensure alternator is properly aligned before torquing. Value is estimated based on typical alternator bolt size.
Battery System
1 Battery Terminal Nuts
M8 x 1.25
1
Battery Terminal Nuts
M8 x 1.25
Torque Specification
12 ft-lbs (16 N-m)
Important Notes
Ensure terminals are clean and free of corrosion before torquing. Value is estimated based on typical battery terminal nut size.
Grounding System
1 Electrical Grounding Bolts
M8 x 1.25
1
Electrical Grounding Bolts
M8 x 1.25
Torque Specification
12 ft-lbs (16 N-m)
Important Notes
Ensure grounding points are clean and free of corrosion before torquing. Value is estimated based on typical grounding bolt size.
Fuse Box System
1 Fuse Box Mounting Bolts
M6 x 1.0
1
Fuse Box Mounting Bolts
M6 x 1.0
Torque Specification
12 ft-lbs (16 N-m)
Important Notes
Ensure fuse box is properly aligned before torquing. Value is estimated based on typical fuse box bolt size.
Wiring Harness System
1 Wiring Harness Connector Bolts
M6 x 1.0
1
Wiring Harness Connector Bolts
M6 x 1.0
Torque Specification
12 ft-lbs (16 N-m)
Important Notes
Ensure wiring harness connectors are properly aligned before torquing. Value is estimated based on typical wiring harness bolt size.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Exhaust Manifold Headers
1 Exhaust Manifold/Headers Bolts
M10 x 1.25
1
Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2 Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
2
Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
Exhaust Pipe Connections
1 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
1
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent warping of the flange.
2 Catalytic Converter to Exhaust Pipe Bolts
M8 x 1.25
2
Catalytic Converter to Exhaust Pipe Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent warping of the flange.
Emissions Control Components
1 EGR Valve Bolts
M6 x 1.0
1
EGR Valve Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent warping of the valve housing.
2 Oxygen Sensor Mounting Bolts
M6 x 1.0
2
Oxygen Sensor Mounting Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar sensor mounting bolts. Ensure bolts are tightened evenly to prevent damage to the sensor.
3 Exhaust Temperature Sensor Bolts
M6 x 1.0
3
Exhaust Temperature Sensor Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar sensor mounting bolts. Ensure bolts are tightened evenly to prevent damage to the sensor.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold Headers
1 Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
1
Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
Exhaust Pipe Connections
1 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
1
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gaskets are properly seated before tightening.
2 Catalytic Converter to Exhaust Pipe Bolts
M8 x 1.25
2
Catalytic Converter to Exhaust Pipe Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure no exhaust leaks after tightening.
3 Muffler to Exhaust Pipe Bolts
M10 x 1.25
3
Muffler to Exhaust Pipe Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment to avoid stress on the exhaust system.
Exhaust Support Components
1 Exhaust Hanger Bolts
M8 x 1.25
1
Exhaust Hanger Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on typical M8 bolt torque specifications.
2 Oxygen Sensor Bolts
M12 x 1.25
2
Oxygen Sensor Bolts
M12 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the sensor is properly seated to avoid damage.
3 Exhaust Flange Bolts
M10 x 1.25
3
Exhaust Flange Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gaskets are properly seated before tightening.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Delivery System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
7.42 ft-lbs (10 N·m)
Important Notes
Ensures a tight seal to prevent fuel leaks and maintain proper fuel pressure.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
7.42 ft-lbs (10 N·m)
Important Notes
Ensures a proper seal to prevent fuel leaks and maintain injector performance.
3 Fuel Pressure Regulator Bolts
M6 x 1.0
3
Fuel Pressure Regulator Bolts
M6 x 1.0
Torque Specification
7.42 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar components. Ensures a secure fit and prevents fuel leaks.
Fuel Storage System
1 Fuel Pump Mounting Bolts
M8 x 1.25
1
Fuel Pump Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures the fuel pump is securely mounted and prevents fuel leaks or pump movement.
2 Fuel Tank Strap Bolts
M8 x 1.25
2
Fuel Tank Strap Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures the fuel tank is securely mounted and prevents movement or fuel leaks.
3 Fuel Filler Neck Bolts
M8 x 1.25
3
Fuel Filler Neck Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures a tight seal to prevent fuel vapor leaks and maintain proper fuel system integrity.
4 Fuel Tank Sender Unit Bolts
M8 x 1.25
4
Fuel Tank Sender Unit Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensures a tight seal to prevent fuel leaks and accurate fuel level readings.
Fuel Filtration System
1 Fuel Filter Bolt/Nut
M8 x 1.25
1
Fuel Filter Bolt/Nut
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures a tight seal to prevent fuel leaks and maintain proper fuel flow.
Fuel Line Connections
1 Fuel Line Fittings
M8 x 1.25
1
Fuel Line Fittings
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensures a tight seal to prevent fuel leaks and maintain system pressure.
Fuel Cap
1 Fuel Cap
N/A (Hand-tightened)
1
Fuel Cap
N/A (Hand-tightened)
Torque Specification
N/A
Important Notes
Hand-tighten until the cap clicks. Ensures a tight seal to prevent fuel vapor leaks and maintain proper fuel system pressure.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Ac Compressor
1 A/C Compressor Mounting Bolts
M10 x 1.5
1
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N-m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute load. Estimated bolt size based on typical A/C compressor applications.
Ac Lines
1 A/C Line Fittings
M12 x 1.25
1
A/C Line Fittings
M12 x 1.25
Torque Specification
N/A
Important Notes
Hand-tighten fittings to avoid damaging O-rings or threads. Estimated bolt size based on typical A/C line applications.
Evaporator Core
1 Evaporator Core Housing Bolts
M6 x 1.0
1
Evaporator Core Housing Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N-m)
Important Notes
Ensure housing is properly aligned before tightening. Estimated bolt size based on typical evaporator housing applications.
Blower Motor
1 Blower Motor Mounting Bolts
M6 x 1.0
1
Blower Motor Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N-m)
Important Notes
Ensure the blower motor is properly aligned before tightening. Estimated bolt size based on typical blower motor applications.
Heater Core
1 Heater Core Inlet/Outlet Pipe Bolts
M8 x 1.25
1
Heater Core Inlet/Outlet Pipe Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N-m)
Important Notes
Ensure O-rings are properly seated before tightening. Estimated bolt size based on typical heater core applications.
Hvac Case
1 HVAC Case Assembly Bolts
M8 x 1.25
1
HVAC Case Assembly Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N-m)
Important Notes
Tighten bolts in a crisscross pattern to evenly distribute load. Estimated bolt size based on typical HVAC case applications.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Strut Shock Absorber
1 Upper Strut Mount Bolts
M10 x 1.25
1
Upper Strut Mount Bolts
M10 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components and bolt size.
2 Strut/Shock Absorber Mounting Bolts
M12 x 1.5
2
Strut/Shock Absorber Mounting Bolts
M12 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure the vehicle is on a level surface before torquing.
3 Lower Shock Absorber Mounting Bolts
M10 x 1.25
3
Lower Shock Absorber Mounting Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated value based on similar components and bolt size.
Control Arms
1 Control Arm Bolts
M10 x 1.25
1
Control Arm Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the vehicle is on a level surface before torquing.
2 Ball Joint Nut
M12 x 1.25
2
Ball Joint Nut
M12 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the ball joint is properly seated before torquing.
Steering Components
1 Tie Rod End Nut
M10 x 1.25
1
Tie Rod End Nut
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the tie rod end is properly seated before torquing.
2 Steering Gear/Rack Bolts
M12 x 1.5
2
Steering Gear/Rack Bolts
M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the steering rack is properly aligned before torquing.
3 Steering Knuckle Bolts
M12 x 1.5
3
Steering Knuckle Bolts
M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Estimated value based on similar components and bolt size.
Sway Bar
1 Sway Bar Link Nut
M10 x 1.25
1
Sway Bar Link Nut
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the sway bar link is properly seated before torquing.
2 Sway Bar Bracket Bolts
M10 x 1.25
2
Sway Bar Bracket Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated value based on similar components and bolt size.
Wheels
1 Wheel Lug Nuts
M12 x 1.5
1
Wheel Lug Nuts
M12 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Use a star pattern to ensure even torque distribution.
Rear Suspension
1 Rear Leaf Spring U-Bolts
M14 x 1.5
1
Rear Leaf Spring U-Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Estimated value based on similar components and bolt size.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the recommended torque setting for lug nuts on a 2005 GMC Canyon?
Q1
What IS the recommended torque setting for lug nuts on a 2005 GMC Canyon?
130-150 foot-pounds (ft-lbs)
Q2 What torque wrench should I use for tightening suspension bolts?
Q2
What torque wrench should I use for tightening suspension bolts?
Use a torque wrench with a range of 10-250 ft-lbs and an accuracy of ±4%
Q3 How do I properly lubricate bolts before applying torque?
Q3
How do I properly lubricate bolts before applying torque?
Apply a small amount of anti-seize lubricant to the threads of the bolt and torque to the specified value
Q4 Can I use a standard wrench to tighten bolts if I don't have a torque wrench?
Q4
Can I use a standard wrench to tighten bolts if I don't have a torque wrench?
No, it IS not recommended to tighten bolts using a standard wrench, as it IS difficult to accurately measure torque
Q5 What are the consequences of over-tightening bolts?
Q5
What are the consequences of over-tightening bolts?
Over-tightening bolts can lead to stripped threads, damaged components, and premature failure
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications to prevent damage and ensure proper assembly. This torque range covers many applications on the GMC Canyon.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Technical Service Bulletins
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.